Maytag Dependable Care Washer Not Spinning

Washer won’t agitate but spins. These parts together are the clutch system for this washer.


40 Washing Machine Ideas Mosogepek Otthon Mosokonyha

Delicate cycle agitation works properly.

Maytag dependable care washer not spinning. Perhaps your washing machine is vibrating during spin cycles or making noises during wash cycles. It's between 6 and 10 years old. Maytag washer, dependable care, 9 cycles.

During the spin cycle, the drum will spin and the pump will operate to remove water. There are two belts under a maytag 'dependable care' washer; Don't stand for this kind of appliance misbehavior.

Is the drain hose kinked, or is the drain clogged? I have a maytag dependable care washer (lat3500) that my wife noticed a smell and that it wasn't spinning. This just might be the last call, the final roundup, the genuine maytag washer's.

One for the main drive pulley and one for the water pump. There are damper pads glued on the base that the washer assembly sits on, these pads are a buffer between the suspension assembly and the base. I have a maytag dependable care washer (model # lat9356aae).

As it spins, it will simultaneously throw water out of the appliance through the drain hose, which empties into a sink or drain pipe. So, i replaced the drive belt. Feel around inside the top of the two tubs to make sure something did not get in between the two keeping it from spinning freely.

Is the end of the drain hose more than 96 (244 cm) above the floor? When i turn the fly wheel clockwise by hand, as in the spin cycle, it turns the drum easily. Not able to edit that first post so starting over.

I have the same problem with our old maytag washer. I noticed that if i pulled back on the motor tension assy, it was able to get enough tension to spin up the drum. Maytag washers, however, like other brands of washers, must be regularly maintained and cleaned.

During the wash cycle, the agitator will not operate and i can hear the motor operating and the belt spinning. One thing to check is the spin bearing, the bearing is inside the top of the brake package. If it does not recognize both water supply hoses are turned on, the control detects a problem with the water pressure sensor.

I have a maytag dependable care top load washer. 16010373 maytag dependable care washer service manual it may not list your exact model number, but the mechanical parts of all the dependable drive washer are basically the same. Returned from vacation a year ago to find that the mother in law unilaterally decided to replace our 20+ year old perfectly reliable and excellent condition maytag dependable care with this pos.

Do you see a lot of suds? This washer is a reversing style of washer, the motor runs one direction to agitate and reverses to drain and spin. But even diligent maintenance won't always prevent your maytag washer from not properly spinning clothes dry, which is a frequent complaint owners have with the machine.

A 70s maytag is in there now, but it is beyond repairing so she just wanted a new maytag. The main drive belt is designed to slip on the motor pulley until the basket comes up to speed so it gets some wear and tear. If your washer won’t agitate but spins, a broken agitator may be to blame.

Thinking that something might be stuck, i manually drained most of the water and attempted the same operation and found that the tub would move slightly (less than a eighth of a turn. Lid is closed, water level is reached appropriately, timer steps through cycle but does not agitate. The water pump belt does not slip and usually wears less.

Why is my maytag top load washer not draining, not spinning, and/or leaving wet loads? Make sure nothing is caught on top of the inner basket or between the inner and outer tank. When you find your washer not agitating but spinning, check for the following common failures, and be sure to disconnect power to your washer:

This washer will usually be well over 10 years old before it will need any repairs at all. (came with the house in 2005). With third load the water filled as usual but the wash cycle did not start.

The motor sits on a roller and spring track, the belt is a cloth/rubber belt. Turns out the belt on the motor pulley was slipping and not turning the drum. Were you washing a large load?

The maytag 'dependable care' washer design is responsible for this and has been around a long time. And she paid the installer to take the dc away. In theory, when your maytag washer reaches its spin cycle, it should begin spinning.

After lots of calling around, he has reached the conclusion that there is no dependable care machine in stock any place in our area, nor do any of the wholesalers have any. Washer does not agitate in regular cycle or permanent press. Was a gentle or delicate cycle or low spin speed selected?

Please make sure both inlet hoses are connected, and both hot and cold water supplies are turned on. It can usually be identified by the two belts it uses which are accessed from the very bottom of the washer and not very deep tub. This washer has sensors that detect the water supply and requires both hoses to have water going to the water valve.

The wash light is lit as … read more I did 2 loads without incident earlier in the day. Although the process is fairly simple, there are a number of problems that may occur.

Read More